TestBenchmark logoTestBenchmark

Stuck Pixel Fixer

This stuck pixel fixer flashes a small patch of random colour noise at your screen's full refresh rate. Park the patch over a stuck pixel — one that glows a fixed colour — and let it run: the rapid switching can free the jammed subpixel. It cannot help a dead pixel, which is black on every colour and is a hardware failure.

A stuck pixel is lit but frozen on one colour. Rapidly changing colour under it — this page flashes a patch of TV-style colour noise at your screen's full refresh rate — can sometimes coax the stuck subpixel back to life.

  • 1. Find the pixel. Use the Dead Pixel Test to locate the stuck pixel and note its position.
  • 2. Park the patch on it. Drag the flashing patch so it fully covers the pixel — bigger than the pixel itself is fine.
  • 3. Let it run. Leave the fixer running for at least 10 to 20 minutes; stubborn pixels are sometimes left for a few hours.
  • 4. Check again. Re-run the Dead Pixel Test on the solid colour where the pixel was stuck.

Honest limits: this can only help a stuck pixel — a subpixel frozen on one colour. A dead pixel (black on every colour) is a hardware failure and no software can revive it. Some stuck pixels also never recover; if the screen is under warranty, a replacement beats hours of flashing.

Includes a flashing-light safety warning before anything flashes · the timer only counts time the fixer is actually on screen

Stuck pixels vs dead pixels

A pixel is made of three subpixels — red, green and blue — each controlled by its own transistor. A stuck pixel has one or two subpixels jammed on (or off), so it glows a constant colour: red, green, blue, cyan, magenta, yellow or white. It shows up most on the colours it disagrees with, and it is the only kind software can help. A dead pixel has lost power to all three subpixels and stays black on every colour; that is physical damage, and it needs a repair or a replacement screen, not a flashing patch.

Find out which you have with the Dead Pixel Test: if the dot changes colour or disappears on some backgrounds, it is stuck; if it is black on white, blue, red and green alike, it is dead.

How long should you run it?

Start with 10 to 20 minutes — many stuck pixels free themselves inside that window, and the auto-stop presets on this page cover the sensible range up to an hour. Stubborn cases are sometimes run for a few hours in a row; there is little evidence that longer marathons add much, and nothing beyond a day is worth your electricity. The timer on this page counts only the time the patch was actually visible and running — time with the tab hidden is excluded, so the number you see is an honest treatment time.

Why might flashing work at all? The liquid crystals in a stuck subpixel can get physically lodged; driving them with rapidly alternating voltages gives them thousands of chances per minute to snap back to their resting alignment. That is also why the gentle-pressure and tapping tricks you will see in forums are risky cousins of the same idea — pressure on modern thin panels can crack or delaminate them, and the flashing patch applies the same persuasion with none of the contact.

Frequently asked questions

How do I fix a stuck pixel?

First confirm it is stuck and not dead using solid colour screens: a stuck pixel glows one colour, a dead pixel is always black. Then park this fixer's flashing noise patch over it and let it run for 10 to 20 minutes to start — longer sessions help some pixels. Recheck on the colour where it showed up. If the screen is under warranty and the pixel bothers you, check the manufacturer's pixel policy before spending hours on software.

What causes a stuck pixel?

Each subpixel is switched by a tiny transistor that drives liquid crystals open or closed. A stuck pixel happens when a subpixel's transistor or crystals get lodged in one state — from a manufacturing defect, a knock, heat, or simple age — so it keeps passing (or blocking) light no matter what the picture asks for. A dead pixel is the more serious cousin: the transistor has failed entirely and the pixel gets no power.

How long does it take to fix a stuck pixel?

When software fixing works at all, it usually works within 10 to 60 minutes of flashing; this tool's auto-stop presets cover that range. Some people run stubborn pixels for a few hours. There is no guaranteed timeline — some stuck pixels recover in minutes, some after hours, and some never recover. The timer here counts only the time the patch was actually on screen in front of you.

What is the difference between a stuck pixel and a dead pixel?

A stuck pixel still lights up but is frozen on one colour — red, green, blue or a mix — because one or two of its subpixels are jammed. A dead pixel is black on every colour because all three subpixels have lost power. Stuck pixels can sometimes be revived with flashing or gentle warmth; dead pixels are hardware failure and cannot be fixed by any software.

Can every stuck pixel be fixed?

No — and any tool that promises a success rate is inventing it. Flashing revives pixels whose crystals are merely lodged; it cannot repair a failed transistor, a damaged panel or a dead pixel, and some stuck pixels are stuck for good. Treat this as a free attempt before a warranty claim, not a guaranteed repair.

How this test works: the fixer draws random red, green and blue values into every pixel of the patch on every animation frame, so each subpixel under the patch is driven on and off at your display's refresh rate. An optional colour-cycle mode rotates pure red, green, blue, white and black instead. The elapsed timer adds up only the time the patch was visible and running, and the auto-stop presets end the session for you.