Speaker Test
This speaker test plays pure tones generated in your browser: a left and right channel check, a 20 Hz to 20 kHz frequency sweep, deep bass tones and a quiet ear-speaker check for phones. Work through the five short steps and finish with a guided verdict that tells you whether your speakers pass - or exactly what to check next.
Start at a comfortable volume. The tones are pure test signals - some frequencies sound much louder than others at the same setting.
Ready - press any test button to begin.
1 · Left and right channels
Each button plays the same clear tone through one side only. With headphones, the tone should sit entirely in the named ear; with speakers, it should clearly lean to that side of the room.
If the left tone comes from the right side, your channels are swapped - check the cable, the balance setting, or simply swap the speakers.
2 · Frequency sweep, 20 Hz to 20 kHz
The tone climbs steadily from the deepest bass to the top of human hearing over 20 seconds. Most speakers stay silent for the first stretch, then fade in. Listen for rattles, buzzes or a side that drops out - and mark where your hearing of it ends.
—
No sweep run yet.
3 · Bass test
Four deep tones, played one at a time. Big speakers and subwoofers should play all four. Small speakers may stay silent or only buzz faintly - a phone or laptop that cannot play 30 Hz is not broken, it is just small.
Tip: if you hear a higher buzzing note instead of a deep hum, that is distortion an octave or two up - the speaker is trying, but it cannot reproduce the real tone.
4 · Phone mode - ear speaker check
Testing a phone? This plays a quiet tone at call volume. Hold the phone to your ear, the way you would on a call, and listen at the earpiece.
Step 1: press the button, then hold the phone to your ear.
- Nothing at the earpiece? Raise media volume, switch silent mode off (the little switch on the side of an iPhone), and disconnect Bluetooth earbuds or the car.
- Muffled or crackly? Take the case off and brush the earpiece grille gently with a clean, dry, soft brush - packed dust is the number one cause.
- Still dead? Restart the phone and try again. If the earpiece works on real calls but stays silent here, your phone simply does not route media sound to it - that is normal on some models.
5 · Your verdict
Answer the four checks from what you just heard, then get your result.
1. Did the tone play only in the left speaker or ear?
2. Did the tone play only in the right speaker or ear?
3. Did the sweep stay audible until at least 12 kHz?
4. Was the 50 Hz bass tone audible, or at least felt as vibration?
How to test your speakers
Step 1 - set up honestly. Set the volume to about half, sit or stand centred between the speakers, and turn off any sound effects, equaliser boosts or "surround" modes in your player or system settings. You want to hear the speakers themselves, not the processing.
Step 2 - check the channels. Play the left tone, then the right. Each should come from its own side, at a similar loudness. If both tones come from one side, something is wrong before you test anything else: a dead channel, a balance slider pushed to one side, or a mono setting.
Step 3 - run the sweep. The climb from 20 Hz to 20 kHz maps what your speakers can actually reproduce. Note where the tone fades in at the bottom (the speaker's real low end) and where it disappears at the top. A rattle or buzz that appears at one particular frequency usually means something loose - a grille, a panel, or the speaker's own surround giving up.
Step 4 - finish with bass and the verdict. Play the bass tones, then answer the four checklist questions. The verdict separates real faults (a silent channel, swapped sides) from simple physics (a phone that cannot play 40 Hz), so you know whether to fix a setting, clean a grille, or accept the limit of the hardware.
Testing a phone speaker
Phones hide two traps. The first is that media volume is not ringtone volume: plenty of "broken" phone speakers are just a media slider sitting at zero. The second is Bluetooth - if your earbuds or your car were connected recently, the phone may be playing this test into an empty room somewhere else entirely.
On an iPhone, also check the silent switch on the side and remember that in landscape the earpiece works as part of the stereo pair, so the channel test leans one tone toward the top of the phone. If the main speaker sounds muffled after a day at the beach or a drop in water, let it dry fully before judging it - and brush dust out of the grilles rather than poking at them. Phone mode in the tool above walks you through the earpiece check the same way.
No sound, crackling, or one silent channel?
No sound at all: confirm the right output device is selected (HDMI monitors and USB headsets steal the default slot constantly), check the system volume and this page's volume slider, then try a different browser tab or app to see whether the silence follows the device.
Crackling or buzzing: lower the volume - if the crackle vanishes, the speaker is being overdriven. A buzz that only appears at one sweep frequency points to something loose resonating. On wired speakers, reseat both ends of the cable; crackle that changes when you wiggle the plug is a dying cable, not a dying speaker.
One silent channel: swap the left and right cables or earbuds. If the silence moves with the cable, the cable is faulty; if it stays on the same side, that speaker or amplifier channel is. On phones, check the balance slider under accessibility settings before assuming hardware damage.
What the sweep tells you
Every speaker has a frequency response - the range it can turn into sound. Big drivers move air easily and start low; small drivers cannot, which is why the first seconds of the sweep are silent on a laptop and thunderous on a home theatre subwoofer. Neither is a fault. What matters is smoothness: a healthy speaker fades in once and stays present, while dips, dropouts and one-sided gaps across the sweep mark real problems - a blown tweeter (the top of the sweep missing), a damaged woofer (rattling in the low mids), or a channel quietly dropping in and out.
At the very top, your own hearing is part of the measurement. Adults commonly stop hearing somewhere between 12 and 17 kHz even on perfect speakers, so use the markers to learn your speakers' range with a listener whose hearing you trust - or compare against a wired pair of headphones on the same device.
Testing a loose speaker with a multimeter
If the speaker is a bare, unconnected unit - a car door speaker on the workbench, a bookshelf driver you just replaced - a multimeter tells you whether its voice coil survived. Set it to resistance and probe the two terminals: a healthy coil reads just under its rated impedance (about 3-6 ohms for a 4-ohm speaker, 6-7 ohms for an 8-ohm one). Zero means a short; an open-circuit reading means the coil is blown. Never probe a speaker that is still wired to a powered amplifier - and for anything plugged into the device in front of you, the tones on this page are the safer and faster test.
Frequently asked questions
How do I test the speaker on my phone?
Play the left and right tones above with the phone in your hand, then run the ear-speaker check in phone mode. On most phones the main speaker should play both tones loudly and clearly. If it stays silent, raise the media volume (not just the ringtone volume), turn off silent mode, and make sure no Bluetooth speaker or car system is connected and quietly taking the sound.
How do I test my iPhone speaker and ear speaker?
Run the channel test with the iPhone in landscape: a healthy iPhone shares stereo between the bottom speaker and the earpiece, so one tone leans to the earpiece side and the other to the bottom. Then use phone mode to check the earpiece on its own. If the earpiece sounds muffled, the usual cause is dust packed into its fine mesh grille - brush it gently with a clean, dry, soft brush, and take the case off to rule it out.
How do I test the ear speaker on an Android phone?
Open phone mode above, play the ear test tone and hold the phone to your ear the way you would on a call. The tone is deliberately quiet, like a caller's voice. If you hear nothing at all, check that media volume is up, clean dust out of the earpiece slit, and restart the phone. Note that a web page plays through your phone's media output, so on models that never route media to the earpiece you will hear the tone from the main speaker instead - that is the phone's routing, not a fault.
Why do I hear sound from only one side?
Work through it in order. Run the channel test again with a different speaker or a pair of earbuds: if the dead side follows the device, the device is faulty; if it stays on the same side of the room, the source or its settings are at fault. Check the balance control (on phones it lives under Accessibility, then hearing or audio settings; on Windows, in the sound settings for your output device), make sure mono audio is off, and try another cable or port.
Why can I not hear the bass tones?
Small speakers physically cannot move enough air to reproduce 30 to 60 Hz. A phone or laptop speaker may produce almost nothing at 50 Hz while working perfectly, while a bookshelf speaker or subwoofer plays the same tone easily. Feeling a faint vibration counts as a pass for small speakers. In the sweep, most laptop speakers only become audible somewhere between 80 and 200 Hz, and that is normal - judge bass on the size of speaker you actually have.
How do I test a speaker with a multimeter?
Only ever do this on a speaker that is fully disconnected from any amplifier. Set the multimeter to resistance (ohms) and touch one probe to each terminal: a healthy voice coil reads a little below its rated impedance, roughly 3 to 6 ohms for a 4-ohm speaker and 6 to 7 ohms for an 8-ohm speaker. A reading near zero means a short circuit, and no reading at all (open circuit) means the coil is blown. The test on this page is for speakers connected to the device you are using now; the multimeter check is for loose, unconnected speakers.
Does this speaker test work on mobile devices?
Yes. Every sound is generated in your browser, so the test works on phones, tablets, laptops and desktops with nothing to install, and phone mode is designed for handheld checks, including the ear speaker. Keep the volume moderate: the sweep and bass tones are pure test signals, and some frequencies can sound harsh at very high volumes even on healthy speakers.
Is anything recorded or sent anywhere?
No. Every sound on this page is generated locally by your browser's audio engine at the moment you press a button. The test never uses your microphone or camera, nothing is recorded, and nothing is uploaded - the results checklist exists only in this page until you leave it.
How this test works: every tone is synthesised live by your browser's audio engine - a sine oscillator routed through a stereo panner for the channel tests, an exponential frequency ramp for the sweep, and low sine tones for the bass check. No audio files are loaded, your microphone is never opened, and the checklist answers exist only in this page's memory.