Battery Test
This battery test reads your live charge level, charging state and drain rate — and answers the question the level alone cannot: how healthy is your battery? Type in your design and full-charge capacities, or drop in your Windows battery report, and get a health percentage with a plain verdict. No download, no sign-up, nothing uploaded.
Click “Check my battery” and the page reads your live battery through the browser's Battery Status API. It works in Chrome, Edge, Opera and Brave — Firefox and Safari do not share battery data at all, so if you see the “not supported” panel below, use the health calculator and the report reader instead: they work in any browser.
Your browser does not share battery data.
The Battery Status API exists only in Chromium browsers (Chrome, Edge, Opera, Brave). Firefox removed it, Safari never implemented it, and on an iPhone every browser is Safari underneath. The live panel above cannot show anything here — but the health calculator and the Windows report reader below work in any browser, because they use numbers from your own device, not the API.
Charging state
—
Time to full / empty
—
Measured rate
—
Full charge lasts
—
The drain rate appears once the level has changed twice — a figure taken from the first minute only shows where in a step the page happened to open.
Level log:
No level changes recorded yet — leave this tab open and use the device normally.
1 · Fast-charging check — is fast charging working?
Plug the device in and keep this page open. After the battery level has changed twice, the box below gives a plain answer. Test between 10% and 60%: fast charging only runs at full power while the battery is fairly empty, and above 80% every battery slows right down, so a test there tells you nothing. Leave the device alone while it measures — gaming or video during the test takes power away from the battery and makes the charger look slower than it is.
No charging measurement yet — plug in and wait for the level to change twice.
Fast means 60% per hour or more (roughly 0 to 50% in under an hour). A basic 5 W charger manages about 20 to 25% per hour on a modern phone. If the verdict is normal or slow and you expected fast, swap the cable first — many cables only carry slow charging — then try the original charger.
2 · Battery health calculator — how much does it still hold?
Battery health is how much of its original capacity a battery still holds. A web page cannot read that, but your device knows the two numbers behind it — type them in and the calculator does the rest. Windows: the battery report lists Design Capacity and Full Charge Capacity in mWh. Mac, iPhone, iPad and recent Android phones: the settings show the percentage directly as Maximum Capacity or Battery health, so there is nothing to calculate — but if you have the two capacities, this calculator gives the same answer.
No health result yet — type the two capacities above.
3 · Windows battery-report reader — let the file do the typing
On a Windows laptop, press Win + R, type cmd and press Enter, then run this command:
powercfg /batteryreport /output "%USERPROFILE%\Desktop\battery-report.html"
A file called battery-report.html appears on your Desktop. Drop it in the box below — the page reads it in your browser only, pulls out the Design Capacity, Full Charge Capacity and Cycle Count, and fills the health calculator above. Nothing is uploaded.
4 · Your battery report
The report reads your live battery, your measured rate, your fast-charging verdict and your health result, and says in plain words what the numbers mean — whether the battery is healthy, worn or due for replacement, and what to do about each. A low health percentage on its own is not a dead battery: it is a worn one, and the report says what that does and does not prove. Copy the text version to paste into a support ticket, a sale listing or a message to a friend.
Go deeper with a dedicated test:
CPU Benchmark Test · GPU Benchmark Test · Refresh Rate Test · FPS Test · Mic Test · Webcam Test · Touch Screen Test
Honest limits
A web page only sees what the browser's Battery Status API exposes: the charge level, whether the device is charging, and the operating system's time estimates. It cannot see battery wear, cycle count, design capacity, temperature or voltage — those need the device's own screens or its battery report, which is why this page has a calculator and a report reader instead of inventing a health number. Firefox and Safari expose nothing at all, and a desktop PC without a battery reports 100% and charging, which is correct and useless. Time estimates jump because they extrapolate the current drain, and a drain rate measured from the first minute is meaningless — this page shows no rate until the level has changed twice. Nothing you type or drop is stored or sent anywhere.
How to test your battery in 3 steps
1 · Read the live battery. Click “Check my battery” above. The page shows your charge level, whether the device is charging or running on battery power, and the operating system's time estimates. Leave the tab open and use the device the way you normally do — after the level has changed twice, the page shows a measured drain rate and how long a full charge lasts at that rate. Here is a worked example. A laptop's battery report lists Design Capacity 56,000 mWh and Full Charge Capacity 42,000 mWh: 42,000 divided by 56,000 times 100 is 75% health, which is 25% wear — below the 80% rule of thumb, so the battery is worn and a replacement is due soon, even though the laptop still reports 100% when it is fully charged. That is the difference between level and health: level says how full it is now, health says how much it can hold at all.
2 · Check the charging. Plug the device in and watch the fast-charging check. Between 10% and 60% charge, fast means 60% per hour or more — roughly 0 to 50% in under an hour. If the verdict is slow and you expected fast, swap the cable first: many cables only carry slow charging. Then try the original charger, and look for a fast-charging switch in the phone's battery settings.
3 · Read the report, not one number. Press “See my battery report”. It puts the live level, the measured rate, the fast-charging verdict and the health result together and says what to do about each. A battery at 75% health that still lasts a working day is a battery to plan around, not an emergency; a battery at 55% that drops from half to zero is a battery to replace. Finish with the rest of the setup on this site — a healthy battery in front of a dead screen corner or a double-clicking mouse is still a bad buy.
What battery health is, and the 80% rule
Battery health is how much charge a battery can hold now compared to when it was new. Every lithium-ion battery loses capacity as it ages: the chemistry degrades a little with every full charge cycle, and faster when the battery is kept hot, kept at 100% for weeks, or drained to zero again and again. Health is the ratio of what it holds now to what it held new — Full Charge Capacity divided by Design Capacity, times 100. A battery at 100% health holds everything it held on day one; at 75% it holds three quarters, so a laptop that lasted eight hours new lasts about six. The 80% line is the one that matters in practice: Apple, Samsung and the major Windows laptop makers all treat a battery as worn below 80% of its original capacity, and it is the threshold for a free replacement while the device is still under warranty or AppleCare+. That is why this page's verdicts change at 80%, not at some rounder number.
Where the real health figure lives
Your device already knows the number — the browser just cannot ask it. On a Windows laptop, the battery report is the source: run powercfg /batteryreport, open the file it creates, and read Design Capacity, Full Charge Capacity and Cycle Count under Installed batteries. The report reader on this page does the reading for you. On a Mac, open System Settings, then Battery, then Battery Health, and read the Maximum Capacity percentage; the cycle count is in System Information under Power, or in the free coconutBattery app. On an iPhone, open Settings, then Battery, then Battery Health, and read Maximum Capacity — iPhone 15 and later also show the cycle count there, and at 80% or below iOS will suggest a replacement. On Android it varies by maker: Samsung has it in the Samsung Members app under Diagnostics, then Battery status; a Pixel 8a or later shows it in Settings, then Battery, then Battery health; other phones hide it, and the dial code *#*#4636#*#* opens a hidden Testing menu with battery information on some of them. On Linux, run upower -i $(upower -e | grep BAT) in a terminal and compare energy-full with energy-full-design.
Why the browser cannot see your battery's wear
It used to be able to, in a way — and the reason it cannot now is privacy, not a missing feature. The Battery Status API was removed from Firefox in 2017 and never implemented in Safari because the combination of charge level, charging state and discharge rate was distinctive enough to help identify a returning visitor across sites: a fingerprint made of power behaviour. Chromium browsers still expose it, which is why this page's live panel works in Chrome, Edge, Opera and Brave and shows nothing in Firefox or Safari. What the API never exposed, in any browser, is the wear data: design capacity, cycle count, cell voltage and temperature were never part of it. That is a hard limit, not a bug to work around — so any page that shows you a health percentage without asking for your report or your settings is guessing, and this page says so instead of guessing.
Fast charging, explained
Fast charging is a rate, not a label on the box. A charger that fills a battery at 60% per hour or more is fast — roughly 0 to 50% in under an hour — while a basic 5 W charger manages about 20 to 25% per hour on a modern phone. The rate is what reaches the battery after the device takes its share, so the charger's rated wattage is always higher than what the battery receives, because of heat losses and the power the device uses while charging. Two things make a fast-charging test meaningless if you ignore them. First, the level: fast charging only runs at full power while the battery is fairly empty, so test between 10% and 60% — above 80% every battery slows right down, by design, to protect the cells. Second, the cable: many cables only carry slow charging, and a fast charger on a slow cable charges slowly. Change one thing at a time — same charger with a different cable, or same cable with a different charger — and compare the rates at a similar battery level, or you cannot tell which one made the difference.
What to do when a battery is worn
If the health figure is below 80%, start with the cheap steps. Run one full calibration cycle: charge to 100%, run on battery until the laptop switches itself off, charge to 100% again — that lets the gauge relearn the real capacity, so the percentage becomes honest, and sometimes the number itself improves. Then change the habits that wear batteries fastest: keep the charge between 20% and 80% when you can, lower the screen brightness (the display is the biggest power draw), close unused tabs and apps, and avoid heat — a laptop left in a hot car ages faster than one used daily. If the battery still drops from half to zero, or the health is below 60%, those steps will not bring it back: the cells are worn out, and the fix is a replacement battery, not another setting. Check the warranty first — Apple replaces a battery at no charge once Maximum Capacity drops below 80% if you are under warranty or AppleCare+, and Dell, HP and Lenovo apply a similar threshold — and look the coverage up by serial number before it expires.
Testing a used laptop before you buy
On a second-hand laptop, the battery is the part sellers hide. Open this page on the seller's computer, click “Check my battery”, unplug the charger and confirm the status changes to running on battery — that alone proves the battery exists and the laptop runs on it. Then make the battery report on that machine and drop it into the report reader: the health percentage and the cycle count are the numbers that decide the price. As a rule of thumb, 90% or above is like-new, 85 to 89% is fine but worth a small discount, 80 to 84% means a replacement is due soon, and below 80% is flagged as worn — verify the figure on the device itself rather than trusting a listing screenshot, since those can be faked. Finish with the rest of the setup on this site — a fast laptop with a worn battery, a dead screen corner or a double-clicking mouse is still a bad buy, and the battery is the most expensive of the three to fix.
Frequently asked questions
Can a website check my battery health?
Only half of it. A website can read your live charge level, whether the device is charging, and the operating system's time estimates — that is what the Battery Status API exposes, and it is what the live panel on this page shows. It cannot read your battery's health: the wear figure, the cycle count, the design capacity and the temperature are never exposed to a web page, on purpose, because the combination of level and drain rate was distinctive enough to help identify a returning visitor. So a page that claims to show your health percentage from the live level alone is inventing it. The honest way is the one this page uses: the health calculator takes the two numbers your own device knows — Design Capacity and Full Charge Capacity, from the Windows battery report or your Mac's Battery settings — and the report reader pulls them straight out of the battery-report.html file for you.
How do I check my laptop battery health?
On a Windows laptop, press Win + R, type cmd and press Enter, then run powercfg /batteryreport and open the battery-report.html file it creates. Look under Installed batteries for Design Capacity and Full Charge Capacity, and divide the second by the first: 42,000 divided by 56,000 is 75% health. The report reader on this page does that step for you — drop the file in and it fills the calculator in. On a Mac, open System Settings, then Battery, then Battery Health, and read the Maximum Capacity percentage; the cycle count is in System Information under Power. On a phone, open Settings, then Battery, then Battery Health on an iPhone, or the Battery section in Settings on a Pixel 8a or later. This page's health calculator takes the numbers from any of those screens and gives you the verdict.
What is a good battery health percentage?
80% or above is generally considered good — that is the line Apple, Samsung and the major Windows laptop makers use, and it is the threshold for a free battery replacement under warranty or AppleCare+. Above 90% is like-new and nothing to think about. From 80% to 89% is normal wear for a laptop that is one to two years old, and you will notice slightly shorter runtime. From 70% to 79% the battery is worn and a replacement is due soon, especially if the laptop shuts down while the meter still shows charge. Below 70% the battery is weak, and below 60% it is worn out: expect sudden shutdowns even at 15% to 25% remaining, and plan a replacement rather than another calibration cycle.
Why does the battery test show no data in my browser?
Because your browser does not expose the Battery Status API. It exists only in Chromium-based browsers — Chrome, Edge, Opera and Brave, on desktop and Android. Firefox removed it in version 52, on privacy grounds, and Safari has never implemented it. On an iPhone every browser is Safari underneath, so an iPhone shows nothing no matter which app you open. There is no way around that from a web page, and no setting to turn it on. The health calculator and the Windows report reader on this page do not depend on the API at all, so on a Windows laptop you can still get the wear answer in any browser: make the battery report, drop it in, and the page reads the capacities from it.
How many charge cycles is too many?
A typical lithium-ion phone battery is rated for about 500 full charge cycles before it drops to 80% of its original capacity, and a modern laptop battery for about 1000 cycles. A cycle is a full 100% of discharge added up, not one plug-in: charging from 50% to 100% twice is one cycle. For a MacBook, under 300 cycles is excellent, 300 to 800 is normal for a used machine, and approaching or passing 1000 means the battery is near end-of-life. But the cycle count alone is not the verdict — a battery with 400 cycles and 92% health is fine, and one with 150 cycles and 68% health is not. Health percentage is the number that matters; cycles are the context that explains it.
Why does the time remaining keep changing?
Because it is an extrapolation from what the battery is doing right now, and what you are doing changes every few seconds. The estimate takes the current rate of discharge and divides the charge left by it, so a minute of video pushes it down and a minute of a still page pushes it back up. That is not a fault in the reading — it is what happens when a rate that varies is projected forward as if it were constant. The measured drain rate on this page has the same character: it is only shown once the level has changed twice, and it follows the last few steps, so it describes what the device is doing now, not an hour ago. Watch the level log instead of the estimate: a line with a steady slope over ten minutes tells you far more than the number does, and a slope that steepens without you doing anything is the interesting signal.
Why does my battery drop from 50% to 0%?
Because the percentage is counted, not measured. The battery's gauge starts from what it believes a full charge holds and subtracts what flows out. When the cells have aged and hold less than the gauge believes, the count still says half at the moment the cells are actually empty: the voltage collapses, and the gauge snaps the number down to match — or the laptop simply switches off. The Windows battery report records these drops, and the level log on this page flags any fall of 10 points or more while it is open. One full cycle — charge to 100%, run on battery until the laptop switches itself off, charge to 100% again — lets the gauge relearn the real capacity, so the percentage becomes honest; if the capacity it then shows is under about 60% of the original, the battery needs replacing, not another calibration.
Does this test work on a desktop or a phone?
On a phone, yes — in a Chromium browser (Chrome, Edge, Opera or Brave on Android). The live panel reads the level, the charging state and the time estimates, and the health calculator takes the Maximum Capacity figure from the phone's own Battery settings. On an iPhone the live panel shows nothing, because every iOS browser is Safari underneath, but the health calculator still works with the number from Settings, then Battery, then Battery Health. On a desktop computer the test has nothing to read: a desktop has no battery, so the browser reports 100% charge and charging, which is correct and useless. Nothing you type, drop or read here is stored or sent anywhere: the test runs entirely in your browser, and closing the tab erases it.
How this test works: the page reads your live battery through the browser's Battery Status API (navigator.getBattery()) and listens for level, charging-state and time changes, so the readings update as the battery does. The drain rate is measured from the moments the level changes — nothing is shown until the level has changed twice. The health calculator divides Full Charge Capacity by Design Capacity and multiplies by 100. The Windows report reader parses your battery-report.html file in the browser with a file reader and extracts the two capacities and the cycle count. No downloads, no sign-up and nothing uploaded.